All information in this manual, including product data, diagrams, charts, etc. represents information on products at the time of publication, and is subject to change without prior notice due to product improvements or other reasons. It is therefore recommended that customers contact Yobiiq B.V. for the latest product information before purchasing a Smart Environment product.
The documentation and product are provided on an “as is” basis only and may contain deficiencies or inadequacies. Yobiiq B.V. takes no responsibility for damages, liabilities or other losses by using this product.
The following symbols are used throughout the manual to emphasize important information and useful tips:
The Tip symbol is used to mark information intended to help you get the most out of your product. It can for example be used to highlight a possible customization option related to the current section
The Note symbol is used to mark information that is important to take into consideration for safety reasons or to assure correct operation of the product.
If you have problem using this product and can’t find the information in this manual, please contact us at any of the following addresses
Yobiiq B.V. Bedrijfsweg 31 6163 CZ Geleen THE NETHERLANDS E-mail: support@yobiiq.com
The following safety precautions must be observed during all phases of the operation, usage, service or repair of any Yobiiq product. Users of the product are advised to convey the following safety information to users and operating personnel and to incorporate these guidelines into all manuals supplied with the product.
Failure to comply with these precautions violates safety standards of design, manufacture and intended use of the product. Yobiiq B.V. assumes no liability for customer’s failure to comply with these precautions.
All instructions must be carefully read before a Yobiiq product is installed and used. They contain important information about how the product is used properly.
The installation of a Yobiiq product should not be started before the technical specifications are fully understood.
The work must be performed in the order listed in this manual, and only by qualified personnel. The work must also be done in accordance with national electrical specifications and applicable local regulations.
In order to avoid the product being damaged by static electricity, an ESD wristband should be worn when handling the product.
The labeling of the product must not be changed, removed or made unrecognizable.
The safety provided by this product is guaranteed only for its intended use. The installation and maintenance of any kind, including the replacement of the product's battery, can only be carried out by qualified personnel.
❗Do not install the equipment close to a heat source or in damp conditions.
The safety provided by this product is guaranteed only for its intended use. The installation and maintenance of any kind, including the replacement of the product's battery, can only be carried out by qualified personnel.
❗Do not install the equipment close to a heat source or in damp conditions.
For your own safety, you must ensure that the product is switched off before carrying out any work on it. Only an authorised person should open the product, if required according to the User Manual as there is a risk of electric shock.
For products that can be powered by an external power supply.
For your safety, the power supply to the product must be SELV (safety extra-low voltage) and must be power limited.
The product must be equipped with an isolating device to cut off the power supply. This should be close to the equipment.
Any electrical connection to the product must be fitted with an overload and short-circuit protection device.
Before using the product, check that the power supply voltage shown in the user manual corresponds to your supply. If it doesn’t, please consult your supplier.
Place the device against a flat, firm and stable surface.
The device must be installed in a location that is sufficiently ventilated so that there is no risk of internal heating and it must not be covered with objects such as newspapers, cloths, curtains, etc.
The product placement must be free and at least 10 cm away from any conducting material.
The device must never be exposed to heat sources such as heating equipment.
Do not place the device close to objects with naked flames such as lit candles, blowtorches, etc.
The device must not be exposed to harsh chemical agents or solvents likely to damage the plastic or corrode the metal parts.
Separate collection and recycling of your waste at the time of disposal will contribute to conserving natural resources and guarantee recycling that respects the environment and human health. For further information concerning your nearest recycling centre, please contact your nearest local authority/town hall offices, your household waste collection company or the distributor where you bought the product.
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste by taking it to a collection point designated for the recycling of electrical and electronic appliances.
